05-25-2016, 07:20 PM | #1 |
Second Lieutenant
27
Rep 289
Posts |
X1 Xenon retrofit ...
Hi Guys,
I have an X1 with Halogen lights... I purchased non AHL Xenon Headlights from EU. I plugged them in .. HALO RINGS + EYEBROWS ( Work but flash ) Blinker is working OK Xenon not turning on, I might have bad bulbs or ballast .. but maybe I need to change some wiring before that will work ? Does anyone have any experience with this ? thank you |
05-25-2016, 07:27 PM | #2 |
Lieutenant
126
Rep 545
Posts
Drives: x3 m40i
Join Date: Feb 2014
Location: Vancouver,BC
|
Have a look at this post in the DIY section on the same topic:
http://e84.xbimmers.com/forums/showthread.php?t=1226068 |
Appreciate
0
|
05-26-2016, 11:18 AM | #4 |
Lieutenant
126
Rep 545
Posts
Drives: x3 m40i
Join Date: Feb 2014
Location: Vancouver,BC
|
|
Appreciate
0
|
05-27-2016, 02:26 PM | #6 |
Lieutenant
126
Rep 545
Posts
Drives: x3 m40i
Join Date: Feb 2014
Location: Vancouver,BC
|
From the pins it should be driven by pin 5.
Does it show any faults? |
Appreciate
0
|
05-27-2016, 02:49 PM | #8 |
Lieutenant
126
Rep 545
Posts
Drives: x3 m40i
Join Date: Feb 2014
Location: Vancouver,BC
|
The plot thickens...
I found more info for you: http://www.e90post.com/forums/showthread.php?t=695805 It seems you need to switch pin 5 and 6 (I did not know this) |
Appreciate
0
|
05-31-2016, 12:48 AM | #9 |
Second Lieutenant
27
Rep 289
Posts |
That did the trick .. it does power the shutters ! thx
With car ON ... Xenon igniter flickers ... Once I coded car with $522 VO ... Xenon IS OK, Bi Xenon is OK ... but I lost angel eyes ...! No idea ... if I need new FRM or power in FRM is now supplied somewhere else |
Appreciate
0
|
05-31-2016, 12:51 AM | #10 |
Lieutenant
126
Rep 545
Posts
Drives: x3 m40i
Join Date: Feb 2014
Location: Vancouver,BC
|
Have you coded DRL to angel eyes?
|
Appreciate
0
|
05-31-2016, 10:50 AM | #11 |
Second Lieutenant
27
Rep 289
Posts |
nope, but wouldn't be that by default ?
I think I might need FRM 3 that supports xenon and move some pins on FRM ... I wonder if I could take 12V from IGN ON and feed directly to AE's thoughts ? |
Appreciate
0
|
05-31-2016, 12:12 PM | #12 |
Captain
25
Rep 673
Posts |
You could certainly put in a controller which bypasses the ECU altogether and goes straight from the battery. Just in this case you won't be able to control them through coding. Also, the car will try to run something else as DRL's, and if you're coming off of a halogen setup that would be high beams. So you would still have to code that out unless you want to run high beams all the time or burn out your HID ballast.
|
Appreciate
0
|
05-31-2016, 01:42 PM | #13 | |
Second Lieutenant
27
Rep 289
Posts |
Quote:
|
|
Appreciate
0
|
05-31-2016, 03:33 PM | #14 | |
Lieutenant
126
Rep 545
Posts
Drives: x3 m40i
Join Date: Feb 2014
Location: Vancouver,BC
|
Quote:
I suggest you measure 7 to see if it had power. Not sure it it will work: Quote from that page: Join pin #1 to pin #7 to get the 3 LED's to function, they will turn on whenever your angel eyes are on. All wiring can be done inside the headlight with wiretaps (since the headlight harness won't have a wire for pin 7 on a non LCI car) and is completely reversible. Last edited by Njerts; 05-31-2016 at 03:39 PM.. |
|
Appreciate
0
|
05-31-2016, 04:30 PM | #15 |
Captain
25
Rep 673
Posts |
If you're looking for a straight source from the battery then there's the jump start post on the passenger side towards the back of the engine compartment (look for the red cap). That's a straight connection to the battery as far as I'm aware.
|
Appreciate
0
|
05-31-2016, 08:47 PM | #16 |
Second Lieutenant
27
Rep 289
Posts |
Progress .. I moved around pins on FRM and rings are ON.. but flickering ...
Xenons not igniting for some reason .. maybe bad bulbs ... Ordered new bulbs ... Any ideas how to get rid flickering my FRM is "AHL" what does that mean ? |
Appreciate
0
|
05-31-2016, 09:09 PM | #17 |
Lieutenant
126
Rep 545
Posts
Drives: x3 m40i
Join Date: Feb 2014
Location: Vancouver,BC
|
Normally turning off voltage monitor will stop flicker on LED's also setting it to max brightness to make sure the FRM does not use PWM to modulate intensity.
|
Appreciate
0
|
05-31-2016, 09:28 PM | #18 |
Captain
25
Rep 673
Posts |
Your bulbs may be just fine. Identify the power wires for the lights and connect them directly to a 12V source (like the battery) capable of 50-60W. If they light, your bulbs and ballasts are fine, if not, well....
|
Appreciate
0
|
06-02-2016, 08:02 PM | #20 |
Second Lieutenant
27
Rep 289
Posts |
Hey
I finally completed the retrofit. Everything is working as expected. Didn't need to replace FRM... x1 came with AHL module... so I highly recommend checking before ordering new one I didn't use harness just the stock cables moved at the plug and frm. I didn't install leveling sensor ... but that's a piece of cake. Thank you to everyone here that was helping. I will write up how to ... shouldn't take longer than 2hrs to install everything |
Appreciate
0
|
06-02-2016, 08:12 PM | #21 |
Lieutenant
126
Rep 545
Posts
Drives: x3 m40i
Join Date: Feb 2014
Location: Vancouver,BC
|
Great, I am glad everything worked out in the end.
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|