XBimmers X1   XBimmers X1
  XBimmers X1

Go Back   XBimmers | BMW X1 Forum > BMW X1 Forums > X1 DIY (Do-It-Yourself) Discussions

Post Reply
 
Thread Tools Search this Thread
      02-03-2013, 03:40 PM   #23
ddoolitt
Registered
0

 
Drives: 2013 BMW X1 xDrive28i
Join Date: Nov 2012
Location: Cambridge, MA


Posts: 1
iTrader: (0)

13140 Curt Hitch

Just finished installing the hitch on our X1 and I agree with Xess about removing the right side covers. I couldn't get the hitch up in there without removing them. I also had to use 6 washers on each stud on the drivers side flange, it is deeper than the passenger's side flange. So after 2 trips to the hardware store, one to get more washers and second to get shorter 18mm socket, I'm done 2 1/2 hours later. I used a small box wrench and channel locks to pop the rivets in place.
Attached Images
     
Appreciate 0
      02-26-2013, 04:09 PM   #24
Cosmickites
New Member
0

 
Drives: X1 xdrive
Join Date: Dec 2012
Location: Long beach ny


Posts: 15
iTrader: (0)

i installed the Curt Hitch today. Very straight forward but a word of warning. it is NEARLY impossible to reach the upper nuts once the hitch is in. Not sure what kind of tool would be best here but even if you get a tool on the upper nuts you are left with about 1/2" of room to turn it. also, through my skill set i broke the hose that connects to the valve at the tail pipe. i was worried that will cause damage to car but apparently people just remove that hose anyway. so the hitch is on and seems pretty sweet. hoping to put my versa haul rack and KTM 200 XCW on it for some adventures
Appreciate 0
      03-29-2013, 03:30 PM   #25
conceyted
Private
1

 
conceyted's Avatar
 
Drives: 2013 X1
Join Date: Oct 2012
Location: New Orleans, LA


Posts: 80
iTrader: (0)

A couple of you have had the Curt Hitch for a month or more. How is it holding up? Do you feel that there are any improvements that could be made to the setup? How about overall appearance? Do you think it blends in will and is not too noticeable? Does it stick out very far from the bottom of the car?
Appreciate 0
      04-10-2013, 09:03 PM   #26
Mtpisgah
Private
2

 
Drives: 2010 WRX & 2013 X1
Join Date: Mar 2013
Location: Greenville, SC


Posts: 70
iTrader: (0)

I installed my Curt hitch tonight. About two hours. I had extra washers on hand since that seems to be an issue, and it was. I did not have to take off the side piece/full bumper cover but I did take off all of the plastic "skid" plates. We will see if I got all of the nuts tight enough when I start pulling my utility trailer.

Last edited by Mtpisgah; 04-11-2013 at 10:08 PM.
Appreciate 0
      04-12-2013, 08:19 AM   #27
Driven2Drive
New Member
0

 
Drives: X1
Join Date: Apr 2013
Location: South


Posts: 8
iTrader: (0)

I will be finishing my install tomorrow due to having to get more washers for the A-Frame support. It appears that my a-frame mounting point is different and requires more spacers than the two included with the kit. I contacted Curt MFG and the engineers said washers would be fine to use as spacers without a problem. This was the first they had seen this issue on the a-frame so here is another heads up. My x1 was built in february of this year and has the premium package as required.
Appreciate 0
      04-12-2013, 06:41 PM   #28
conceyted
Private
1

 
conceyted's Avatar
 
Drives: 2013 X1
Join Date: Oct 2012
Location: New Orleans, LA


Posts: 80
iTrader: (0)

Quote:
Originally Posted by Driven2Drive View Post
I will be finishing my install tomorrow due to having to get more washers for the A-Frame support. It appears that my a-frame mounting point is different and requires more spacers than the two included with the kit. I contacted Curt MFG and the engineers said washers would be fine to use as spacers without a problem. This was the first they had seen this issue on the a-frame so here is another heads up. My x1 was built in february of this year and has the premium package as required.
Can you please take a few pictures once installed. Thank you.
Appreciate 0
      06-05-2013, 01:15 PM   #29
qkbrian
New Member
0

 
Drives: BMW X1
Join Date: Dec 2012
Location: Houston, Tx


Posts: 21
iTrader: (0)

Has anyone tried a Draw-Tite hitch? A local shop indicated they would install this one with wiring harness, ball mount, ball pin & clip for around $450.


http://www.draw-tite.com/content/pro...040&part=75761
Appreciate 0
      06-22-2013, 02:09 PM   #30
conceyted
Private
1

 
conceyted's Avatar
 
Drives: 2013 X1
Join Date: Oct 2012
Location: New Orleans, LA


Posts: 80
iTrader: (0)

Quote:
Originally Posted by qkbrian View Post
Has anyone tried a Draw-Tite hitch? A local shop indicated they would install this one with wiring harness, ball mount, ball pin & clip for around $450.


http://www.draw-tite.com/content/pro...040&part=75761
I am eyeing it. Compared to the Curt, the DrawTite hitch offers another 150 lbs of tongue weight and another 1000 lbs of pulling capacity. The price is very close to the Curt, though a tiny bit more expensive, and the designs appear identical.
Appreciate 0
      06-26-2013, 11:58 AM   #31
dashate
Registered
0

 
Drives: X1 S281
Join Date: Jun 2013
Location: Sarasota


Posts: 1
iTrader: (0)

Quote:
Originally Posted by conceyted View Post
"For the Panoramic Sunroof only" ?? What the...?
So, I can't install this on a non-sunroof X1? What's the sunroof got to do with all this?
Appreciate 0
      07-10-2013, 12:16 PM   #32
ledlover
New Member
3

 
Drives: Valencia Orange X1 sdrive
Join Date: Apr 2013
Location: NC


Posts: 25
iTrader: (0)

Anyone got a wiring harness that works for X1? I am buying a hitch to pull a travel trailer about 2700lbs and need to connect the wiring for lights
Appreciate 0
      07-11-2013, 03:07 PM   #33
wkl_nj
Registered
0

 
Drives: X1 sDrive
Join Date: Nov 2012
Location: NJ


Posts: 2
iTrader: (0)

no Panoramic Sunroof == no A-Frame. it can't support the tongue weight. Mine x1 has the same problem, no hitch is available. sucks
Appreciate 0
      12-05-2013, 05:46 PM   #34
Youpaiyou
Enlisted Member
0

 
Drives: X1
Join Date: Dec 2013
Location: Southern CA


Posts: 33
iTrader: (0)

Quote:
Originally Posted by wkl_nj View Post
no Panoramic Sunroof == no A-Frame. it can't support the tongue weight. Mine x1 has the same problem, no hitch is available. sucks
There isn't anything available to us?
Appreciate 0
      12-05-2013, 08:36 PM   #35
Youpaiyou
Enlisted Member
0

 
Drives: X1
Join Date: Dec 2013
Location: Southern CA


Posts: 33
iTrader: (0)

I just read the curt hitch installation instructions and sure enough, it specifically states that it only works with X1s with a panoramic sunroof due to the A-Frame.

Are there any alternatives out there for folks without the panoramic sunroof?
Appreciate 0
      12-06-2013, 04:24 PM   #36
cwickberg
Private First Class
1

 
Drives: X1 35i MSport Ultimate
Join Date: Oct 2013
Location: United States


Posts: 116
iTrader: (0)

Quote:
Originally Posted by Youpaiyou View Post
I just read the curt hitch installation instructions and sure enough, it specifically states that it only works with X1s with a panoramic sunroof due to the A-Frame.

Are there any alternatives out there for folks without the panoramic sunroof?
perhaps you could just order the a frame and bolt in it place?
Appreciate 0
      12-06-2013, 07:00 PM   #37
Youpaiyou
Enlisted Member
0

 
Drives: X1
Join Date: Dec 2013
Location: Southern CA


Posts: 33
iTrader: (0)

Quote:
Originally Posted by cwickberg View Post
perhaps you could just order the a frame and bolt in it place?
Well, I ordered my X1 today so I just added the panoramic sunroof. At least i discovered this issue before placing my order. I'll create another thread about my order.
Appreciate 0
      12-21-2013, 12:10 PM   #38
Fastone5353
Registered
0

 
Drives: BMW 135i
Join Date: Dec 2013
Location: Westerville, OH


Posts: 2
iTrader: (0)

Does anyone make a 1 1/4" receiver hitch? The Curt Hitch is a 2" which really is overkill for carrying a bicycle rack.
Appreciate 0
      07-23-2014, 08:32 AM   #39
kaio123
Registered
0

 
Drives: bmw x1 xdrive28i
Join Date: Jul 2014
Location: chicago


Posts: 1
iTrader: (0)

guys, i was thinking of installing the curt hitch on my 2013 X1 xdrive28i without the sunroof. the picture of the x1 here does not seem to have a sunroof. are there any options for us without sunroof to install a hitch ?
Appreciate 0
      07-28-2014, 07:54 PM   #40
themishmosh
Private First Class
1

 
Drives: BMW X1 xDrive35i
Join Date: Apr 2014
Location: United States


Posts: 127
iTrader: (0)

Quote:
Originally Posted by Fastone5353 View Post
Does anyone make a 1 1/4" receiver hitch? The Curt Hitch is a 2" which really is overkill for carrying a bicycle rack.
I would agree. But no one makes a 1 1/4" hitch. Thankfully, my 2 bike Kuat rack with 1 1/4" has an available adapter to 2" that I bought for $30 shipped.

Quote:
Originally Posted by kaio123
are there any options for us without sunroof to install a hitch ?
Are you towing or using it to hold a bike rack? I would think that if you didn't actually tow, that center arm to the A-frame would not be needed.
Appreciate 0
Post Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 01:31 AM.




xbimmers
Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST